| Mode | Contents |
|---|---|
| MODE page 01h |
SCSI Read-write error recovery page: Parameters can be saved Automatic write reallocation is enabled Automatic read reallocation is enabled Drive will repeat read operations 11 times Drive will repeat write operations 5 times Drive will employ a maximum of 65535 ms to recover data |
| MODE page 02h |
SCSI Disconnect-Reconnect mode page: Parameters can be saved 128 ratio of buffer that shall be full prior to attempting a reselection 128 ratio of buffer that shall be empty prior to attempting a reselection 1000 µs maximum permitted to assert BSY without a REQ/ACK handshake Data transfer disconnect control is not used |
| MODE page 03h |
SCSI Format device page: Parameters can be saved 4522 tracks per zone to use in dividing the capacity for the purpose of allocating alternate sectors 0 sectors per zone that shall be reserved for defect handling 8 tracks per zone that shall be reserved for defect handling 0 tracks per LUN that shall be reserved for defect handling 720 physical sectors per track 512 Bytes per physical sector Target-dependent interleave value is 1 102 sectors between last block of one track and first block of the next 102 sectors between last block of a cylinder and first block of the next one Drive supports hard-sectoring format Sector addressing is progressively incremented in one cylinder before going to the next |
| MODE page 04h |
SCSI Rigid disk drive geometry page: Parameters can be saved 2 heads 49855 cylinders Write pre-compensation starts at cylinder 0 Write current reduction starts at cylinder 0 Heads park in cylinder 0 Medium rotates at 10033 rpm Spindle synchronization is disable or unsupported |
| MODE page 07h |
SCSI Verify error recovery page: Parameters can be saved Drive will repeat verify operations 11 times Drive will employ a maximum of 65535 ms to recover data |
| MODE page 08h |
SCSI Caching mode page: Parameters can be saved Write-cache is enabled Drive does not distinguish between cached read data Drive does not distinguish between cached write data Pre-fetch will be done for READ commands of 65535 blocks or less A maximum of 65535 blocks will be pre-fetched A maximum of 65535 blocks will be pre-fetched even if it is commanded to pre-fetch more Pre-fetch can continue across discontinuities (such as cylinders or tracks) Drive should have 32 cache segments |
| MODE page 0Ah |
SCSI Control mode page: Parameters can be saved Global logging target save disabled The logical unit maintains one task set for all nexuses Commands should be sent strictly ordered If ACA is established, the task set commands shall resume after it is cleared, otherwise they shall terminate with CHECK CONDITION LUN shall clear unit attention condition reported in the same nexus On medium insertion, it shall be loaded for full access A maximum of 76800 ms are allowed to remain busy |
| MODE page 19h | Unknown mode page |
| MODE page 19h subpage 01h | Unknown mode page |
| MODE page 19h subpage 02h | Unknown mode page |
| MODE page 19h subpage 03h | Unknown mode page |
| MODE page 19h subpage 04h | Unknown mode page |
| MODE page 1Ah |
SCSI Power condition page: Parameters can be saved Standby timer Z is set to 400 ms Idle timer A is set to 100 ms |
| MODE page 1Ch |
SCSI Informational exceptions control page: Parameters can be saved Informational exceptions are enabled No reporting of informational exception condition Informational exception conditions will be reported a maximum of 1 times Warning reporting is enabled |
| MODE page 00h | Unknown vendor mode page |
| EVPD | Contents |
|---|---|
| EVPD page 00h | Undecoded |
| EVPD page 81h | |
| EVPD page C0h | Undecoded |
| EVPD page C1h | Undecoded |
| EVPD page C2h | Undecoded |
| EVPD page C3h | Undecoded |
| EVPD page D1h | Undecoded |
| EVPD page D2h | Undecoded |