Aaru Report for
YAMAHA
CRW2200E
1.0D
ATAPI characteristics:
ATAPI device
Model: YAMAHA CRW2200E
Firmware revision: 1.0D
Supported ATA versions: ATA-1 ATA/ATAPI-4
Maximum ATA revision supported: Minor ATA version not specified
Parallel ATA device:
PIO timing mode: 3
DMA timing mode: 2
Advanced PIO: PIO0 PIO1
Multi-word DMA: MDMA0 MDMA1 MDMA2
Ultra DMA: UDMA0 UDMA1 UDMA2 (active)
ATAPI CD-ROM/DVD/etc device
Device shall set DRQ within 50 µs of receiving PACKET
ATAPI device uses 12 byte command packet
Device capabilities:
IORDY is supported and can be disabled
DMA is supported
At minimum 120 ns. transfer cycle time per word in MDMA, 120 ns. recommended
At minimum 120 ns. transfer cycle time per word in PIO, without flow control
At minimum 120 ns. transfer cycle time per word in PIO, with IORDY flow control
Command set and features:
28-bit LBA is supported
SCSI characteristics:
Vendor: YAMAHA
Product: CRW2200E
Revision: 1.0D
Device is connected and supported.
CD-ROM/DVD/etc device
Device claims to comply with ANSI X3.131:1994 (SCSI-2)
Device does not claim to comply with any SCSI ECMA standard
Device does not claim to comply with any SCSI ISO/IEC standard
Device is removable
Device supports synchronous data transfer
Device does not support asymmetrical access
Device supports only ST clocking
Device supports MODE SENSE (6)
Device supports MODE SENSE (10)
Device supports MODE SENSE subpages
SCSI mode sense pages:
| Mode |
Contents |
|
MODE page 01h
|
SCSI Read error recovery page for MultiMedia Devices:
Drive will repeat read operations 8 times
All available recovery procedures will be used.
Recovered errors will not be reported.
Unrecovered ECC errors will return CHECK CONDITION.
Drive will repeat write operations 3 times
|
|
MODE page 02h
|
SCSI Disconnect-Reconnect mode page:
1 ratio of buffer that shall be empty prior to attempting a reselection
Data transfer disconnect control is not used
|
|
MODE page 05h
|
SCSI Flexible disk page:
Transfer rate: 199 kbit/s
10 heads
8192 cylinders
0 sectors per track
0 bytes per sector
Write pre-compensation starts at cylinder 0
Write current reduction starts at cylinder 0
Drive steps in 15000 μs
Heads settles in 822400 μs
Target shall wait 320 seconds before attempting to access the medium after motor on is asserted
Target shall wait 320 seconds before releasing the motor on signal after becoming idle
The motor on signal shall remain released
Drive needs to do 1 step pulses per cylinder
Write pre-compensation is 32
Head takes 32 ms to load
Head takes 32 ms to unload
Medium rotates at 8224 rpm
Pin 34 indicates disk has changed when active low Pin 4 indicates eject when active low Pin 2 is unconnected
Pin 1 is unconnected
|
|
MODE page 08h
|
SCSI Caching mode page:
Write-cache is enabled
Drive does not distinguish between cached read data
Drive does not distinguish between cached write data
Pre-fetch will be done for READ commands of 65535 blocks or less
A maximum of 65535 blocks will be pre-fetched
A maximum of 65535 blocks will be pre-fetched even if it is commanded to pre-fetch more
|
|
MODE page 0Dh
|
SCSI CD-ROM parameters page:
Drive will remain in track hold state a vendor-specified time after a seek or read
Each minute has 60 seconds
Each second has 75 frames
|
|
MODE page 0Eh
|
SCSI CD-ROM audio control parameters page:
Drive will return from playback command immediately
Output port 0 has channels 0 at maximum volume
Output port 1 has channels 1 at maximum volume
|
|
MODE page 1Ah
|
SCSI Power condition page:
Drive will not enter standy mode
Drive will not enter idle mode
|
|
MODE page 1Dh
|
Undecoded
|
|
MODE page 2Ah
|
SCSI CD-ROM capabilities page:
Drive can play audio
Drive can read sectors in Mode 2 Form 1 format
Drive can read sectors in Mode 2 Form 2 format
Drive supports multi-session discs and/or Photo-CD
Drive can read digital audio
Drive can continue from streaming loss
Drive can read uncorrected and interleaved R-W subchannels
Drive can read, deinterleave and correct R-W subchannels
Drive can read Media Catalogue Number
Drive can read ISRC
Drive uses a tray
Drive can lock media
Drive is not locked, media can be ejected and inserted
Drive can eject media
Each channel can be muted independently
Each channel's volume can be controlled independently
Drive supports 256 volume levels
Drive has 8192 Kbyte of buffer
Drive's maximum reading speed is 7056 Kbyte/sec.
Drive's current reading speed is 7056 Kbyte/sec.
Drive can read and write CD-R
Drive supports reading CD-R packet media
Drive can read and write CD-RW
Drive's current writing speed is 3528 Kbyte/sec. in CLV mode
Drive supports writing at 3528 Kbyte/sec. in CLV mode
Drive supports test writing
Drive supports buffer under-run free recording
|
|
MODE page 30h
|
Unknown mode page
|
SCSI CD-ROM capabilities:
Drive can continue from streaming loss
Drive can eject media
Drive can lock media
Drive can play audio
Drive can read and write CD-R
Drive can read and write CD-RW
Drive can read digital audio
Drive can read ISRC
Drive can read Media Catalogue Number
Drive can read sectors in Mode 2 Form 1 format
Drive can read sectors in Mode 2 Form 2 format
Drive can read uncorrected and interleaved R-W subchannels
Drive can read, deinterleave and correct R-W subchannels
Drive has 8192 Kbyte of buffer
Drive is not locked, media can be ejected and inserted
Drive supports 256 volume levels
Drive supports buffer under-run free recording
Drive supports multi-session discs and/or Photo-CD
Drive supports reading CD-R packet media
Drive supports test writing
Drive supports writing at 3528 Kbyte/sec. in CLV mode
Drive uses a tray
Drive's current reading speed is 7056 Kbyte/sec.
Drive's current writing speed is 3528 Kbyte/sec. in CLV mode
Drive's maximum reading speed is 7056 Kbyte/sec.
Each channel can be muted independently
Each channel's volume can be controlled independently
SCSI MMC features:
2048 bytes per logical block
4 media blocks are required for the binding nonce
Drive can do a test writing in Session at Once Mode
Drive can do a test writing in Track at Once Mode
Drive can do a test writing with DVDs
Drive can eject media
Drive can format media into logical blocks
Drive can lock media
Drive can overwrite a SAO track with another in CD-RWs
Drive can overwrite a TAO track with another in CD-RWs
Drive can read and write DVD+R
Drive can read and write DVD+R DL
Drive can read and write DVD+RW
Drive can read BD-ROM
Drive can read CD-ROM
Drive can read DVD
Drive can read HD DVD-ROM, HD DVD-RW and HD DVD-R
Drive can return CD-Text from Lead-In
Drive can return Spare Area Information
Drive can write BD-R on Pseudo-OverWrite SRM mode
Drive can write BD-R or BD-RE
Drive can write CD-RW
Drive can write CDs in Session at Once and in Raw Modes:
Drive can write CDs in Track at Once Mode:
Drive can write user provided data in the R-W subchannels in Session at Once Mode
Drive claims capability to read all CD formats according to OSTA Multi-Read Specification
Drive firmware is dated 3/19/2011 12:34:56 PM
Drive is able to access Hybrid discs
Drive is to report drive serial number
Drive shall report Read/Write Error Recovery mode page
Drive supports 1 AGIDs concurrently
Drive supports AACS version 1
Drive supports C2 Error Pointers
Drive supports Device Busy events
Drive supports DVD CPRM version 1
Drive supports DVD CSS/CPPM version 1
Drive supports generating the binding nonce
Drive supports Microcode Upgrade
Drive supports set/release of PWP status
Drive supports the Informational Exceptions Control mode page 1Ch
Drive supports writing DVD-R, DVD-RW and DVD-R DL
Drive supports zero loss linking in Session at Once Mode
Drive supports zero loss linking in Track at Once Mode
Drive supports zero loss linking writing DVDs
Drive uses a tray
Drive uses Serial ATAPI interface
Tested media:
Information for medium named "Audio CD"
Medium type code: 00h
Drive recognizes this medium.
Logical sector size: 2048 bytes
READ LONG sector size: 2048 bytes
Device can use the READ CAPACITY (10) command with this medium
Device can use the READ CD command with LBA addressing with this medium
Device can use the READ CD command with MM:SS:FF addressing with this medium
Device can use the PIONEER vendor READ CD-DA command with this medium
Device can use the PIONEER vendor READ CD-DA MSF command with this medium
Device can use the PLEXTOR vendor READ CD-DA command with this medium
Device can report the C2 pointers when reading from this medium
Device can correct subchannels when reading from this medium
Device can read the Table of Contents from this medium, without processing it
Device can read the P to Q subchannels from this medium
Device can read the P to Q subchannels from this medium reporting the C2 pointers
Device can read the R to W subchannels from this medium
Device can read the Table of Contents from this medium
Information for medium named "CD-R"
Medium type code: 00h
Drive recognizes this medium.
Logical sector size: 2048 bytes
READ LONG sector size: 2048 bytes
Device can use the READ CAPACITY (10) command with this medium
Device can use the READ (6) command with this medium
Device can use the READ (10) command with this medium
Device can use the READ (12) command with this medium
Device can use the READ CD command with LBA addressing with this medium
Device can use the READ CD command with MM:SS:FF addressing with this medium
Device can use the READ CD command with LBA addressing with this medium to read raw sector
Device can use the READ CD command with MM:SS:FF addressing with this medium read raw sector
Device can use the HL-DT-ST vendor READ DVD (RAW) command with this medium
Device can use the PLEXTOR vendor READ DVD (RAW) command with this medium
Device can read the CD Absolute-Time-In-Pregroove from this medium
Device can report the C2 pointers when reading from this medium
Device can correct subchannels when reading from this medium
Device can read the Table of Contents from this medium, without processing it
Device can read the Power Management Area from this medium
Device can read the P to Q subchannels from this medium
Device can read the P to Q subchannels from this medium reporting the C2 pointers
Device can read the R to W subchannels from this medium
Device can read the Table of Contents from this medium
Information for medium named "CD-ROM"
Medium type code: 00h
Drive recognizes this medium.
Logical sector size: 2048 bytes
READ LONG sector size: 2048 bytes
Device can use the READ CAPACITY (10) command with this medium
Device can use the READ (6) command with this medium
Device can use the READ (10) command with this medium
Device can use the READ (12) command with this medium
Device can use the READ CD command with LBA addressing with this medium
Device can use the READ CD command with MM:SS:FF addressing with this medium
Device can use the READ CD command with LBA addressing with this medium to read raw sector
Device can use the READ CD command with MM:SS:FF addressing with this medium read raw sector
Device can use the HL-DT-ST vendor READ DVD (RAW) command with this medium
Device can read the CD Absolute-Time-In-Pregroove from this medium
Device can report the C2 pointers when reading from this medium
Device can correct subchannels when reading from this medium
Device can read the Table of Contents from this medium, without processing it
Device can read the Power Management Area from this medium
Device can read the P to Q subchannels from this medium
Device can read the P to Q subchannels from this medium reporting the C2 pointers
Device can read the R to W subchannels from this medium
Device can read the Table of Contents from this medium
Information for medium named "CD-RW (marked 4x or lower)"
Medium type code: 00h
Drive recognizes this medium.
Logical sector size: 2048 bytes
READ LONG sector size: 2048 bytes
Device can use the READ CAPACITY (10) command with this medium
Device can use the READ (6) command with this medium
Device can use the READ (10) command with this medium
Device can use the READ (12) command with this medium
Device can use the READ CD command with LBA addressing with this medium
Device can use the READ CD command with MM:SS:FF addressing with this medium
Device can use the READ CD command with LBA addressing with this medium to read raw sector
Device can use the READ CD command with MM:SS:FF addressing with this medium read raw sector
Device can use the PLEXTOR vendor READ DVD (RAW) command with this medium
Device can read the CD Absolute-Time-In-Pregroove from this medium
Device can report the C2 pointers when reading from this medium
Device can correct subchannels when reading from this medium
Device can read the Table of Contents from this medium, without processing it
Device can read the Power Management Area from this medium
Device can read the P to Q subchannels from this medium
Device can read the P to Q subchannels from this medium reporting the C2 pointers
Device can read the R to W subchannels from this medium
Device can read the Table of Contents from this medium
Information for medium named "CD-RW High Speed (marked between 8x and 12x)"
Medium type code: 00h
Drive recognizes this medium.
Logical sector size: 2048 bytes
READ LONG sector size: 2048 bytes
Device can use the READ CAPACITY (10) command with this medium
Device can use the READ (6) command with this medium
Device can use the READ (10) command with this medium
Device can use the READ (12) command with this medium
Device can use the READ CD command with LBA addressing with this medium
Device can use the READ CD command with MM:SS:FF addressing with this medium
Device can use the READ CD command with LBA addressing with this medium to read raw sector
Device can use the READ CD command with MM:SS:FF addressing with this medium read raw sector
Device can use the HL-DT-ST vendor READ DVD (RAW) command with this medium
Device can use the PLEXTOR vendor READ DVD (RAW) command with this medium
Device can read the CD Absolute-Time-In-Pregroove from this medium
Device can report the C2 pointers when reading from this medium
Device can correct subchannels when reading from this medium
Device can read the Table of Contents from this medium, without processing it
Device can read the Power Management Area from this medium
Device can read the P to Q subchannels from this medium
Device can read the P to Q subchannels from this medium reporting the C2 pointers
Device can read the R to W subchannels from this medium
Device can read the Table of Contents from this medium
Information for medium named "CD-RW Ultra Speed (marked 16x or higher)"
Medium type code: 00h
Drive recognizes this medium.
Logical sector size: 2048 bytes
READ LONG sector size: 2048 bytes
Device can use the READ CAPACITY (10) command with this medium
Device can use the READ (6) command with this medium
Device can use the READ (10) command with this medium
Device can use the READ (12) command with this medium
Device can use the READ CD command with LBA addressing with this medium
Device can use the READ CD command with MM:SS:FF addressing with this medium
Device can use the READ CD command with LBA addressing with this medium to read raw sector
Device can use the READ CD command with MM:SS:FF addressing with this medium read raw sector
Device can use the HL-DT-ST vendor READ DVD (RAW) command with this medium
Device can use the PLEXTOR vendor READ DVD (RAW) command with this medium
Device can read the CD Absolute-Time-In-Pregroove from this medium
Device can report the C2 pointers when reading from this medium
Device can correct subchannels when reading from this medium
Device can read the Table of Contents from this medium, without processing it
Device can read the Power Management Area from this medium
Device can read the P to Q subchannels from this medium
Device can read the P to Q subchannels from this medium reporting the C2 pointers
Device can read the R to W subchannels from this medium
Device can read the Table of Contents from this medium
Information for medium named "Enhanced CD (aka E-CD, CD-Plus or CD+)"
Medium type code: 00h
Drive recognizes this medium.
Logical sector size: 2048 bytes
READ LONG sector size: 2048 bytes
Device can use the READ CAPACITY (10) command with this medium
Device can use the HL-DT-ST vendor READ DVD (RAW) command with this medium
Device can use the PLEXTOR vendor READ DVD (RAW) command with this medium