Mode | Contents |
---|---|
MODE page 01h |
SCSI Read-write error recovery page: Parameters can be saved Automatic write reallocation is enabled Automatic read reallocation is enabled Drive will repeat read operations 63 times Drive will repeat write operations 63 times Drive will employ a maximum of 8000 ms to recover data |
MODE page 02h |
SCSI Disconnect-Reconnect mode page: Parameters can be saved 1000 µs maximum permitted to assert BSY without a REQ/ACK handshake Data transfer disconnect control is not used |
MODE page 03h |
SCSI Format device page: Parameters can be saved 520 tracks per zone to use in dividing the capacity for the purpose of allocating alternate sectors 0 sectors per zone that shall be reserved for defect handling 0 tracks per zone that shall be reserved for defect handling 100 tracks per LUN that shall be reserved for defect handling 3169 physical sectors per track 512 Bytes per physical sector Target-dependent interleave value is 1 760 sectors between last block of one track and first block of the next 308 sectors between last block of a cylinder and first block of the next one Drive supports hard-sectoring format Sector addressing is progressively incremented in one cylinder before going to the next |
MODE page 04h |
SCSI Rigid disk drive geometry page: Parameters can be saved 10 heads 328806 cylinders Write pre-compensation starts at cylinder 0 Write current reduction starts at cylinder 0 Heads park in cylinder 0 Medium rotates at 7200 rpm Spindle synchronization is disable or unsupported |
MODE page 07h |
SCSI Verify error recovery page: Parameters can be saved Drive will repeat verify operations 63 times Drive will employ a maximum of 8000 ms to recover data |
MODE page 08h |
SCSI Caching mode page: Parameters can be saved Drive does not distinguish between cached read data Drive does not distinguish between cached write data Pre-fetch will be done for READ commands of 65535 blocks or less A maximum of 65535 blocks will be pre-fetched even if it is commanded to pre-fetch more Pre-fetch can continue across discontinuities (such as cylinders or tracks) Drive should not reorder the sequence of write commands to be faster Drive should have 8 cache segments |
MODE page 0Ah |
SCSI Control mode page: Parameters can be saved The logical unit maintains one task set for all nexuses Commands should be sent strictly ordered If ACA is established, the task set commands shall resume after it is cleared, otherwise they shall terminate with CHECK CONDITION LUN shall clear unit attention condition reported in the same nexus On medium insertion, it shall be loaded for full access A maximum of 3068700 ms are allowed to remain busy |
MODE page 18h | Unknown mode page |
MODE page 19h | Unknown mode page |
MODE page 19h subpage 01h | Unknown mode page |
MODE page 19h subpage 02h | Unknown mode page |
MODE page 19h subpage 03h | Unknown mode page |
MODE page 1Ah |
SCSI Power condition page: Parameters can be saved Drive will not enter standy mode Idle timer A is set to 2000 ms Idle timer B is set to 600000 ms Performing background functions take precedence over maintaining low power conditions |
MODE page 1Ch |
SCSI Informational exceptions control page: Parameters can be saved Informational exceptions are enabled Only report informational exception condition on request Drive shall log informational exception conditions Timer interval is 600000 ms Background functions are enabled |
MODE page 1Ch subpage 01h |
SCSI Background Control page: Parameters can be saved Background medium scans are enabled 24 hours shall be between the start of a background scan operation and the next At least 250 ms must be idle before resuming a suspended background scan operation At most 2000 ms must be before suspending a background scan operation and processing received commands |
MODE page 21h | Unknown mode page |
EVPD | Contents |
---|---|
EVPD page 00h | Undecoded |
EVPD page 83h |
SCSI Device identification: Identifier belongs to addressed logical unit NAA: 50:00:03:95:38:E0:BD:F4 Identifier belongs to target port Descriptor referes to Serial Attachment SCSI protocol NAA: 50:00:03:95:38:E0:BD:F6 Identifier belongs to target port Descriptor referes to Serial Attachment SCSI protocol Relative target port identifier: 1 Identifier belongs to target device that contains the addressed logical unit Descriptor referes to Serial Attachment SCSI protocol NAA: 50:00:03:95:38:E0:BD:F5 Identifier belongs to target device that contains the addressed logical unit Descriptor referes to Serial Attachment SCSI protocol SCSI name string identifier: naa.5000039538E0BDF5 |
EVPD page 86h |
SCSI Extended INQUIRY Data: Logical unit supports type 1 protection Device supports head of queue Device supports the ORDERED task attribute Device supports the SIMPLE task attribute Device supports marking a block as uncorrectable with WRITE LONG Device supports disabling correction with WRITE LONG Device has a volatile cache Extended self-test takes 08:32:00 to complete |
EVPD page 8Ah | Undecoded |
EVPD page 90h | Undecoded |
EVPD page B1h | Undecoded |
EVPD page DCh | Undecoded |