Aaru Device Report

ATAPI characteristics:
ATAPI device
Model: SONY HiFD SFD200
Firmware revision: 1264
Supported ATA versions: ATA/ATAPI-4
Maximum ATA revision supported: Minor ATA version not specified
Parallel ATA device:
Advanced PIO: PIO0 PIO1
Multi-word DMA: MDMA0 MDMA1 MDMA2 (active)

ATAPI Direct-access device
Device shall set DRQ within 3 ms of receiving PACKET
ATAPI device uses 12 byte command packet
Device capabilities:
IORDY is supported
DMA is supported
At minimum 120 ns. transfer cycle time per word in MDMA, 120 ns. recommended
At minimum 250 ns. transfer cycle time per word in PIO, without flow control
At minimum 120 ns. transfer cycle time per word in PIO, with IORDY flow control
Command set and features:
NOP is supported and enabled
DEVICE RESET is supported and enabled
PACKET is supported and enabled
Power management is supported and enabled
Removable media feature set is supported and enabled
28-bit LBA is supported
Removable Media Status Notification is supported
Removable Media Status Notification feature set is supported

SCSI characteristics:
Vendor: SONY (Sony Corporation Japan)
Product: HiFD
Revision: 1264
Device is connected and supported.
Direct-access device
Device claims to comply with ANSI X3.408:2005 (SPC-3)
Device does not claim to comply with any SCSI ECMA standard
Device does not claim to comply with any SCSI ISO/IEC standard
Device is removable
Device supports setting Normal ACA
Device supports LUN hierarchical addressing
Device does not support assymetrical access
Device supports only ST clocking
Device supports MODE SENSE (6)

SCSI mode sense pages:

Mode	Contents
MODE page 01h	SCSI Read-write error recovery page: Automatic write reallocation is enabled Automatic read reallocation is enabled Drive will repeat read operations 32 times Drive will repeat write operations 32 times
MODE page 03h	SCSI Format device page: 11570 tracks per zone to use in dividing the capacity for the purpose of allocating alternate sectors 2049 sectors per zone that shall be reserved for defect handling 0 tracks per zone that shall be reserved for defect handling 0 tracks per LUN that shall be reserved for defect handling 34 physical sectors per track 512 Bytes per physical sector Target-dependent interleave value is 0 0 sectors between last block of one track and first block of the next 0 sectors between last block of a cylinder and first block of the next one Drive supports hard-sectoring format Drive media is removable Sector addressing is progressively incremented in one surface before going to the next
MODE page 05h	SCSI Flexible disk page: Transfer rate: 28000 kbit/s 13 heads 890 cylinders 34 sectors per track 512 bytes per sector Write pre-compensation starts at cylinder 0 Write current reduction starts at cylinder 0 Target shall wait 0 seconds before attempting to access the medium after motor on is asserted Target shall wait 0 seconds before releasing the motor on signal after becoming idle Drive needs to do 1 step pulses per cylinder Medium rotates at 3600 rpm Pin 34 is unconnected Pin 4 is unconnected Pin 2 is unconnected Pin 1 is unconnected
MODE page 07h	SCSI Verify error recovery page: Drive will repeat verify operations 32 times
MODE page 08h	SCSI Caching mode page: Write-cache is enabled Drive does not distinguish between cached read data Drive does not distinguish between cached write data No pre-fetch will be done
MODE page 0Bh	SCSI Medium types supported page: Supported medium type one: Unknown medium type 0x40 Supported medium type two: Unknown medium type 0x42
MODE page 1Bh	SCSI Removable Block Access Capabilities page: Drive supports reporting progress of format Drive supports 1 LUNs
MODE page 1Ch	SCSI Informational exceptions control page: Informational exceptions are enabled Unknown method of reporting 13