Aaru Report for SEAGATE ST336704LSUN36G 0326

SCSI characteristics:
Vendor: SEAGATE (Seagate)
Product: ST336704LSUN36G
Revision: 0326
Device is connected and supported.
Direct-access device
Device claims to comply with ANSI X3.301:1997 (SPC-1)
Device does not claim to comply with any SCSI ECMA standard
Device does not claim to comply with any SCSI ISO/IEC standard
Device supports LUN hierarchical addressing
Device supports 16-bit wide SCSI addresses
Device supports 16-bit wide data transfers
Device supports synchronous data transfer
Device supports linked commands
Device supports CONTINUE TASK and TARGET TRANSFER DISABLE commands
Device supports TCQ queue
Device does not support asymmetrical access
Device supports ST and DT clocking
Device supports MODE SENSE (6)
Device supports MODE SENSE (10)
Drive supports DPO and FUA bits

Device has 71132959 blocks of 512 bytes each
Device size: 36420075008 bytes, 36 Gb, 33.92 GiB
Medium type code: 00h
Long block size: 549 bytes
Device supports READ CAPACITY (10) command.
Device supports READ (6) command.
Device supports READ (10) command.
Device supports READ LONG (10) command.

SCSI mode sense pages:
Mode Contents
MODE page 01h SCSI Read-write error recovery page:
Parameters can be saved
Automatic write reallocation is enabled
Automatic read reallocation is enabled
Data not recovered within limits shall be transferred back before a CHECK CONDITION
Drive shall report recovered errors
Drive will repeat read operations 11 times
Drive will repeat write operations 5 times
Drive will employ a maximum of 65535 ms to recover data
MODE page 02h SCSI Disconnect-Reconnect mode page:
Parameters can be saved
128 ratio of buffer that shall be full prior to attempting a reselection
128 ratio of buffer that shall be empty prior to attempting a reselection
1000 µs maximum permitted to assert BSY without a REQ/ACK handshake
Data transfer disconnect control is not used
MODE page 03h SCSI Format device page:
Parameters can be saved
0 tracks per zone to use in dividing the capacity for the purpose of allocating alternate sectors
0 sectors per zone that shall be reserved for defect handling
0 tracks per zone that shall be reserved for defect handling
0 tracks per LUN that shall be reserved for defect handling
107 physical sectors per track
512 Bytes per physical sector
Target-dependent interleave value is 1
0 sectors between last block of one track and first block of the next
0 sectors between last block of a cylinder and first block of the next one
Drive supports hard-sectoring format
Sector addressing is progressively incremented in one cylinder before going to the next
MODE page 04h SCSI Rigid disk drive geometry page:
Parameters can be saved
27 heads
24622 cylinders
Write pre-compensation starts at cylinder 0
Write current reduction starts at cylinder 0
Heads park in cylinder 0
Medium rotates at 10025 rpm
Spindle synchronization is disable or unsupported
MODE page 07h SCSI Verify error recovery page:
Parameters can be saved
Drive will repeat verify operations 11 times
Drive will employ a maximum of 65535 ms to recover data
MODE page 08h SCSI Caching mode page:
Parameters can be saved
Drive does not distinguish between cached read data
Drive does not distinguish between cached write data
Pre-fetch will be done for READ commands of 65535 blocks or less
A maximum of 118 blocks will be pre-fetched
A maximum of 65535 blocks will be pre-fetched even if it is commanded to pre-fetch more
Device should use number of cache segments or cache segment size for caching
Pre-fetch can continue across discontinuities (such as cylinders or tracks)
Drive should not reorder the sequence of write commands to be faster
Drive should have 2 cache segments
MODE page 0Ah SCSI Control mode page:
Parameters can be saved
Global logging target save disabled
The logical unit maintains one task set for all nexuses
Commands should be sent strictly ordered
If ACA is established, the task set commands shall resume after it is cleared, otherwise they shall terminate with CHECK CONDITION
LUN shall clear unit attention condition reported in the same nexus
On medium insertion, it shall be loaded for full access
A maximum of 135000 ms are allowed to remain busy
MODE page 1Ah SCSI Power condition page:
Parameters can be saved
Standby timer Z is set to 400 ms
Idle timer A is set to 100 ms
MODE page 1Ch SCSI Informational exceptions control page:
Parameters can be saved
Informational exceptions are enabled
Unconditionally generate recovered error on informational exceptions
Informational exception conditions will be reported a maximum of 1 times Warning reporting is enabled
MODE page 33h Unknown mode page
MODE page 34h Unknown mode page
MODE page 00h Unknown vendor mode page

SCSI extended vital product data pages:
EVPD Contents
EVPD page 00h Undecoded
EVPD page 81h SCSI Implemented operating definitions:
Default operating definition: SCSI-3
Current operating definition: SCSI-3
Supported operating definitions:
SCSI-3
EVPD page C0h Undecoded
EVPD page C1h Undecoded
EVPD page C2h Undecoded
EVPD page C3h Undecoded
EVPD page D1h Undecoded
EVPD page D2h Undecoded